Volvo D5 injector test: cylinder balance and fuel correction
A five-cylinder Volvo diesel that idles rough, shakes or smokes is often blamed on "an injector" — but which one? The engine module can answer that itself: it measures how fast each cylinder turns the crankshaft and how much fuel it has to add or take away to keep them even.
What the engine module measures
At idle, a diesel engine module does not simply inject the same amount of fuel into every cylinder. It watches the crankshaft speed during each cylinder's power stroke and trims the fuel cylinder by cylinder until they all push equally hard. The size of that trim is a direct record of how far each injector is from nominal.
Volvo's five-cylinder diesel engine module exposes this as two routines in its own catalog:
- cylinder selective engine speed — the speed each of the five cylinders produces, in rpm;
- cylinder quantity correction test — the fuel correction applied to each cylinder, in milligrams per stroke.
Workshop software presents the pair as one check, usually called the injector or cylinder balance test. Neither routine changes anything in the module: they only measure.
Which cars have this test
The procedure described here belongs to the five-cylinder diesel of the P1 cars: the C30 (2007–2011), S40 and V50 (2006–2011) and the second-generation C70 (2006–2009), with the Bosch EDC16 engine module. Our own test car, a 2008 C70 with the D5244T8 engine, is one of them. If you are not sure which platform your car is on, see Volvo P1, P2 and P3 platforms.
The later P3 diesels with the EDC17 engine module have a counterpart, the fuel balance test, built the same way: start a routine, read five per-cylinder values, stop. The identifiers, units and limits are that module's own, so the numbers below should not be carried over to those cars.
Before you start
The test compares cylinders at a steady idle, so anything that disturbs the idle disturbs the result. The preconditions are short:
- no stored fault codes in the engine module, or their causes already fixed — see Volvo fault codes explained;
- engine at operating temperature;
- air conditioning off;
- engine idling, car stationary, in neutral or P with the parking brake on, in a ventilated place.
Safety: the engine runs for the whole check. Do not unplug injector connectors while it is running to "find the dead cylinder" — on these engines an injector can stay open and flood the cylinder with fuel.
Part one: speed per cylinder
Once the first routine is started, the module reports five engine-speed values, one per cylinder, and keeps updating them. Give them a few seconds to settle.
At a normal warm idle every cylinder sits at about 675–725 rpm, and — more important than the absolute number — close to the others. One cylinder clearly slower or faster than the rest means combustion in that cylinder differs: uneven compression, a poor contact or corrosion in the injector connector, or the injector itself.
Speed alone cannot tell those causes apart. That is what the second part is for.
Part two: fuel quantity correction
The second routine reports how much the module adjusts each cylinder's fuel to keep the speeds even, in mg per stroke. The module's limit is ±4 mg per stroke: beyond that it has run out of room to compensate.
The sign is the part people get backwards:
| Correction | What the module is doing | What it says about the injector |
|---|---|---|
| Above 0 | Adding fuel to this cylinder | Delivers less than nominal |
| Around 0 | Nothing to correct | Delivers what is asked |
| Below 0 | Removing fuel from this cylinder | Delivers more than nominal |
A correction is the module's reaction, not the fault itself: it shows that a cylinder needs help, not why. That is why it is never read on its own.
Reading the two together
The check becomes useful when the two parts are read for the same cylinder. An injector, or its connector, is the likely cause when both of these hold:
- the cylinder runs fast and its correction is near −4 mg per stroke — the injector over-delivers, and the module cannot take away enough fuel; or
- the cylinder runs slow and its correction is near +4 mg per stroke — the injector under-delivers, and the module cannot add enough.
In both cases the correction is pinned at its limit and the speed is still off in the direction the correction was fighting. That is the picture in the illustration at the top: cylinder 3 at 741 rpm with −3.8 mg per stroke, next to four cylinders near 700 rpm with corrections close to zero.
What the test cannot tell you
The balance check narrows the search to a cylinder; it does not prove the injector is faulty. The conclusion only stands once a mechanical cause has been ruled out with a cylinder leakage test: if that test shows a fault, the injectors are unlikely to be the problem.
Leakage and compression tests, injector return-flow measurement and wiring checks are workshop jobs. So is the last step people forget: after injectors are replaced, the engine module has to be programmed for the new ones.
How a tool runs it
On the P1 diesels the engine module speaks Volvo's D2 messages (see the Volvo D2 protocol explained). The check is a short conversation with the engine module:
- start the cylinder speed routine, wait about a second, then read the five speed values repeatedly;
- stop it;
- start the fuel quantity routine and read the five correction values, each a 16-bit number that the module's definition scales to hundredths of a milligram per stroke;
- stop it.
None of this exists in legislated OBD-II. A generic scanner can show the single overall engine speed, but it has no request for starting a routine inside a Volvo engine module and no identifiers for per-cylinder values — the same gap that keeps it from reading the electronic oil level.
The stop requests matter as much as the start. The routines run inside the module, so a tool has to end them when you leave the screen, when a step fails, and when the connection drops. Volscan does all three.
Status: Volscan includes this check for the P1 five-cylinder diesels, built from the engine module's own definitions, and we are still confirming it on our C70 — the module's answers and timing have not been recorded on the car yet. On a 2017 XC60 diesel, the EDC17 counterpart ran in October 2026: the module accepted the routine and returned five per-cylinder values for each part.
FAQ
What is a normal injector correction value on a Volvo D5?
On the five-cylinder diesels of the C30, S40, V50 and C70, the engine module's fuel quantity correction is measured in milligrams per stroke and its limit is ±4 mg per stroke. Values close to zero mean the injector delivers about what the module asks for; a cylinder sitting near +4 or −4 is at the edge of what the module can compensate.
Does a positive correction mean the injector delivers too much fuel?
No, the other way round. A positive correction means the engine module is adding fuel to that cylinder, so the injector delivers less than nominal. A negative correction means the module is removing fuel, so the injector delivers more than nominal.
Can a generic OBD-II scanner run the Volvo injector balance test?
No. The test is a routine inside the engine module that is started and stopped with Volvo's own diagnostic requests, and the per-cylinder values are read with Volvo's own identifiers. Legislated OBD-II has no equivalent for either.
Does the injector test change anything in the engine module?
No. Both parts of the test only measure. They do run inside the engine module while the engine idles, so they have to be stopped again when the check is finished or the connection is lost.